EUTECH INSTRUMENTS ALPHA COND 500 - REV 4 Specifiche Scaricare il pdf (Pagina 54)

Transmitter Cond/Res 2-Channel M300 54

Printed in Switzerland 52 121 318

11.2.3 Calibrate Unlock

Select this Menu to conﬁgure the CAL Menu, see Section 7.

Selecting Yes means that Meter and Analog Output calibration Menus will be selectable under

the CAL Menu. Selecting No means that only the Sensor calibration is available under the CAL

Menu.

Press [ENTER] after the selection to display a conﬁrmation screen.

11.3 Tech Service

(PATH: Menu/Tech Service)

Note: This Menu is for Mettler Toledo Service personnel use only.

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 63 64

Operation Manual 1
Conductivity/Resisitivity 1
2-Channel 1
Transmitter M300 1
1 Introduction 7
2 Safety instructions 7
3 Unit overview 9
3.3 Control/Navigation Keys 11
3.3.6 “Save changes” dialog 13
3.3.7 Security Passwords 13
3.4 Display 13
4 Installation instruction 14
2 Terminal for sensor 19
4.3 Connector PIN deﬁnition 20
6 Quick Setup 21
6.3 Measurement Units 22
6.4 Analog Outputs 22
6.5 Setpoint 23
7 Sensor Calibration 24
7.5 Sensor Veriﬁcation 27
8 Conﬁguration 28
8.2.1 Channel Setup 29
8.2.2 Temperature Source 29
8.2.4 Set Averaging 31
8.3 Analog Outputs 31
8.4 Setpoints 33
8.5 Alarm/Clean 36
8.5.1 Alarm 36
8.5.2 Clean 37
8.6 Display 37
8.6.1 Measurement 37
8.6.2 Resolution 38
8.6.3 Backlight 38
8.6.4 Name 38
8.7 Hold Analog Outputs 39
9 System 40
9.3 Passwords 41
9.3.1 Changing Passwords 41
9.4 Set/Clear Lockout 41
9.5 Reset 42
9.5.1 Reset System 42
10 PID Setup 43
10.1 Enter PID Setup 44
10.2 PID Auto/Manual 44
10.3 Mode 45
10.3.1 PID Mode 45
10.4 Tune Parameters 45
10.4.3 Proportional Limits 46
10.4.4 Corner Points 46
10.5 PID Operation 46
11 Service 47
11.1.2 Digital Input 48
11.1.3 Display 48
11.1.4 Keypad 48
11.1.5 Memory 49
11.1.6 Set Relay 49
11.1.7 Read Relays 49
11.1.8 Set Analog Outputs 50
11.1.9 Read Analog Outputs 50
11.2 Calibrate 51
11.2.1 Calibrate Meter 51
11.2.2 Calibrate Analog 53
11.2.3 Calibrate Unlock 54
11.3 Tech Service 54
12 Info 55
12.2 Calibration Data 56
12.3 Model/Software Revision 56
13 Maintenance 57
14 Troubleshooting 57
14.1 Changing the Fuse 58
16 Speciﬁcations 59
17 Default tables 61
18 Waranty 62
19 UL Statement (Pending) 62
Addresses 64

Commenti su questo manuale

Nessun commento

EUTECH INSTRUMENTS ALPHA COND 500 - REV 4 Specifiche Pagina 54

Commenti su questo manuale

Prodotti e manuali riguardandi Misurazione, test & controllo EUTECH INSTRUMENTS ALPHA COND 500 - REV 4